User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Iotech 1200:Data Acquisition System
DATE:                  04-Aug-97
AUTHOR:                User Contributed
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       3
NUMBER OF LINES:       97
CONFIGURATION:         Fluke 5700A
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-   R     N              P             M              F        W
  1.002  ASK+                                          X
  1.003  HEAD         INITIAL CONDITIONS
  1.004  DISP         With No power applied to the UUT, remove any installed
  1.004  DISP         card.
  1.005  DISP         Remove both top and bottom covers.
  1.006  DISP         Remove the four screws that secure's the scanning
  1.006  DISP         module cover to the PCB.  Also remove the two screws
  1.006  DISP         that secure's the module cover to the back panel.
  1.007  DISP         Reinsert the scanning card into it's edge connector.
  1.008  DISP         Remove shorting connectors from JP2 and JP3, located
  1.008  DISP         to the right of the edge connector.
  1.009  DISP         Connect the IEEE cable from PORT 1 to the UUT.
  1.010  DISP         Set switch 9 on the IEEE bus address switch to
  1.010  DISP         the UP position.
  1.011  DISP         Apply power to the UUT and allow 1 hour of warm up time.
  1.012  IEEE         *RX[D6000]
  1.013  IEEE         *CX[D500]
  1.014  HEAD         {}
  1.015  HEAD         {* Chassis Offset Calibration *}
  1.016  JMP          2.001
  1.017  EVAL
  2.001  IEEE         K12345X
  2.002  IEEE         E?X[I$]
  2.003  IEEE         U2X[I]
  2.004  MATH         mem1 = mem - 128
  2.005  JMPF         2.020
  2.006  JMPT         2.020
  2.007  DISP         Connect the Fluke 5700 HI/LO OUTPUT to UUT JP2 HI
  2.007  DISP         and JP3 LO.
  2.008  5700         0V                                                S  2W
  2.009  HEAD         Please Wait Performing Offset Calibration
  2.010  IEEE         H0X[D32000]
  2.011  IEEE         E?X[I$]
  2.012  HEAD         * Chassis Offset Calibration *
  2.013  IEEE         U2X[I]
  2.014  MATH         mem1 = mem - 128
  2.015  JMPF         2.020
  2.016  JMPT         2.020
  2.017  RSLT         =Chassis Offset Calibration sucessfully performed
  2.018  RSLT         =as per paragraph 7.2.1.2 in the Multiscan 1200 manual.
  2.019  JMP          2.023
  2.020  DISP         [MEM1]
  2.020  DISP         Calibration error. See page 6.72 in manual.
  2.021  IEEE         EX
  2.022  JMP          3.030
  2.023  HEAD         {}
  2.024  HEAD         {* Chassis Gain Calibration *}
  2.025  HEAD
  2.026  JMP          3.001
  2.027  EVAL
  3.001  5700         -4.4V                                             S  2W
  3.002  HEAD         Please Wait Performing - Gain Calibration
  3.003  IEEE         G0,91X[D32000]
  3.004  IEEE         E?X[I$]
  3.005  IEEE         U2X[I]
  3.006  MATH         mem1 = mem - 128
  3.007  JMPF         3.013
  3.008  JMPT         3.013
  3.009  RSLT         =Negative Chassis Gain Calibration sucessfully performed
  3.010  RSLT         =as per paragraph 7.2.1.3 in the Multiscan 1200 manual.
  3.011  IEEE         E?X[I$]
  3.012  JMP          3.014
  3.013  DISP         [MEM1]
  3.013  DISP         Calibration error. See page 6.72 in manual.
  3.014  5700         4.4V                                              S  2W
  3.015  HEAD         Please Wait Performing + Gain Calibration
  3.016  IEEE         G0,91X[D32000]
  3.017  IEEE         E?X[I$]
  3.018  IEEE         U2X[I]
  3.019  MATH         mem1 = mem - 128
  3.020  JMPF         3.028
  3.021  JMPT         3.028
  3.022  HEAD         {}
  3.023  RSLT         =Positive Chassis Gain Calibration sucessfully performed
  3.024  RSLT         =as per paragraph 7.2.1.3 in the Multiscan 1200 manual.
  3.025  IEEE         E?X[I$]
  3.026  IEEE         EX
  3.027  JMP          3.030
  3.028  DISP         [MEM1]
  3.028  DISP         Calibration error. See page 6.72 in manual.
  3.029  IEEE         EX
  3.030  DISP         Reset switch 9 to it's DOWN position.
  3.031  HEAD         {}
  3.032  END